Nutanix ncp-mci-v6-5 practice test

What is a requirement to enable Flow Networking?

• A. How Microsegmentation must be enabled.
• B. Prism Central is using a three-node scale out deployment.
• C. A dedicated virtual switch has been created for Flaw Networking.
• D. Microservices Infrastructure (CMSP) is enabled.

What does Nutanix recommend when setting up the node networking?

• A. Include at least two physical interfaces in every bond.
• B. Combine NIC models from different vendors in the same bond.
• C. Include NIC models from different vendors in the same bond.
• D. Combine 1 GbE interfaces and 10 GbE interfaces in the same bond.

An administrator wishes to perform LCM updates as quickly as possible due to time constraints with maintenance windows.
Which action should the administrator take, prior to beginning an LCM update, to minimize delays?

• A. Enable automatic NCC updates
• B. Manually migrate VMs to a single host
• C. Add vCPUs to each CVM
• D. Disable any VM affinity rules

On a Nutanix cluster, what does Network Segmentation refer to?

• A. Isolating management traffic from storage replication traffic.
• B. Physically separating management traffic from guest VM traffic.
• C. Isolating intra-cluster traffic from guest VM traffic.
• D. A distributed firewall for securing VM to VM traffic.

An administrator needs to increase bandwidth available to the AHV host and to the CVM.
How should the administrator complete this task?

• A. Use manage_ovs commands to update br0 to change the configuration to Active-Active.
• B. In Prism, create vs1 interface and add any remaining uplinks.
• C. Use manage_ovs commands to create br1 and add any remaining uplinks.
• D. In Prism, update vs0 to change the configuration to Active-Active.

Which two types of granular RBAC does Nutanix provide for AHV hosts? (Choose two.)

• A. Closter based
• B. Category based
• C. Disk based
• D. Project based

An administrator is setting up a Nutanix cluster for a mission critical workload. All of the VMs in the cluster must have capacity to continue to run even if there is a hardware failure.
What should the administrator enable to achieve this requirement?

• A. Change the fault tolerance level to Block.
• B. Enable HA Reservation in Prism Element.
• C. Change the redundancy factor to 3.
• D. Enable Degraded Node Detection.

Refer to the exhibit.

An administrator wants to replace an old node with a node of a newer generation in a 3-node cluster. The administrator has already chosen the appropriate node, but is unable to remove it from the cluster.
Why is the Remove Host option not shown in the exhibit?

• A. The host needs to be placed into Maintenance Mode before.
• B. It is not possible to remove a node from a 3-node cluster.
• C. It is only possible to remove a host from a cluster using CLI.
• D. The host needs to be removed from the cluster using Prism Central.

An administrator is performing validation testing of a newly deployed cluster. During this test, the administrator disconnects each LAN interface from each of the nodes while pinging the hypervisor and guest VMs.
When the first interface is disconnected, pings continue as expected to the hypervisor, but pings stop responding from the guest. Pings continue when the interface is reconnected. When the second interface is disconnected, pings continue to both the hypervisor and guest VMs.
What could be the cause of this error?

• A. One of the network interfaces has a bad patch cable
• B. Portfast is not enabled on the switch ports
• C. Switch ports are configured with different VLANs
• D. This is normal behavior for LAN Failover

An administrator is tasked with configuring networking on an AHV cluster and needs to optimize for maximum single VM throughput.
Which bond mode should the administrator select?

• A. Active-Active
• B. Active-Active with Mac Pinning
• C. Active-Backup
• D. No Uplink Bond